Where to Put Knobs and Pulls on Kitchen Cabinets (With Diagrams)
Knobs go on the corner opposite the hinges, 2 to 3 inches in from each edge: the bottom corner of upper doors and the top corner of base doors. Center pulls on drawers.
Put knobs on the corner opposite the hinges: the bottom corner of upper cabinet doors and the top corner of base cabinet doors, about 2 to 3 inches in from both edges. Center pulls on drawers.
The goal is hardware you reach without stretching or bending: low on wall cabinets and high on base cabinets.
Knobs: opposite the hinge, 2 to 3 inches from the side and from the bottom (upper doors) or top (base doors). Drawer pulls: centered side to side, in the middle of the front or 2 to 3 inches below the top edge. On drawers 30 to 36 inches wide, use two pulls or one long pull.
The placement chart, diagrams and six install tools are below.
Product links go to Amazon. As an Amazon Associate, Kitchen Guide 101 earns from qualifying purchases.
Cabinet Hardware Tools Compared
All 6 side by side. Tap any name to see it on Amazon.
| Tool | Type | Use on | When | Best for | Price |
|---|---|---|---|---|---|
| Cabinet Hardware Jig for Knobs and Pulls | Drill guide | Doors and drawers | Before drilling | A full kitchen | $$ |
| 12-Inch Combination Square | Measuring tool | Edges and centers | Marking | Checking spacing | $ |
| 3/16-Inch Brad Point Drill Bit | Drill bit | Wood doors and drawers | Drilling | Standard 8-32 screws | $ |
| Breakaway Cabinet Hardware Screws, 8-32 | Screws | Doors and drawers | Installing | Odd door thicknesses | $ |
| Stainless Steel Bar Pulls, 25 Pack | Hardware | Drawers and doors | Finishing | Modern kitchens | $$ |
| Round Cabinet Knobs, 25 Pack | Hardware | Doors | Finishing | Shaker doors | $$ |
Details are as stated on each Amazon listing at time of writing and can change. Price tiers: $ under $20 · $$ $20–50.
6 Tools for Installing Knobs and Pulls
A jig, a square and the right drill bit make placement exact. Hardware packs come last.
Cabinet Hardware Jig for Knobs and Pulls
A jig sets the spacing once and repeats it on every door. The guide holes keep the drill bit straight, so knobs and pulls line up across the kitchen.
Check the hole spacing range on the listing against the pulls you plan to buy.
- Same spot on every door
- Straight holes
- Less measuring
- Takes a few minutes to set up
- Check the hole spacing range
12-Inch Combination Square
The tool for measuring in from an edge. Lock the head at your chosen distance and every mark lands the same way on every door.
It also checks that a pull sits square to the drawer edge.
- Repeatable marks
- Squares lines to the edge
- Useful for other projects
- Not a drill guide
- Measure twice on framed doors
3/16-Inch Brad Point Drill Bit
Most knob and pull screws in the United States are 8-32 machine screws, which pass through a 3/16-inch hole. A brad point starts exactly on the mark and cuts a clean hole.
Clamp a scrap block behind the door so the back face does not splinter.
- Starts on the mark
- Clean holes
- Low price tier
- Check your screw size first
- Metric hardware can differ
Breakaway Cabinet Hardware Screws, 8-32
Doors and drawer fronts vary in thickness. Breakaway screws snap off at the length you need, so a screw is never too short or poking through.
They help most on drawers with a separate decorative front.
- One pack fits many depths
- Low price tier
- Handy for doubled fronts
- Check the thread size
- Snap with pliers
Stainless Steel Bar Pulls, 25 Pack
Bar pulls suit modern and transitional kitchens. One bulk pack in a single finish keeps every drawer and door matched.
Check the hole spacing, called center-to-center, before you buy.
- Matched finish
- Easy to grip
- Enough for most kitchens
- Hole spacing must match
- Two holes per pull
Round Cabinet Knobs, 25 Pack
Knobs need only one hole, so they are the simplest hardware to fit. They suit shaker doors and small drawers.
On a shaker door, pick a knob no wider than the door frame it sits on.
- One hole each
- Quick to fit
- Classic look
- Can spin if not tightened
- Smaller grip than a pull
Where to Put Cabinet Knobs and Pulls: Placement Chart
| Hardware | Where it goes | Spacing |
|---|---|---|
| Knob on an upper door | Bottom corner, opposite the hinge | 2 to 3 in from the side and bottom edges |
| Knob on a base door | Top corner, opposite the hinge | 2 to 3 in from the side and top edges |
| Pull on an upper door | Vertical, on the side opposite the hinge | Bottom end 2 to 3 in above the bottom edge |
| Pull on a base door | Vertical, on the side opposite the hinge | Top end 2 to 3 in below the top edge |
| Knob on a shaker door | Centered on the frame (the stile) | Where the stile meets the bottom rail on uppers, the top rail on base doors |
| Pull on a drawer | Centered side to side | Middle of the front, or 2 to 3 in below the top |
| Pull on a shaker drawer | Centered on the top rail | Middle of the rail, or the middle of the center panel |
| Wide drawer, 30 to 36 in | Two pulls, or one long pull | Each pull centered in its half (9 in from each edge on 36 in) or on the one-third lines |
Whatever spacing you choose, use it on every door and drawer, on wall and base cabinets alike.
Knob and Pull Placement Diagrams
Gold lines show the measurement from each edge.
Where to Put Pulls on Drawers
Center side to side
Measure the drawer front and mark the middle.
Slab fronts: middle or high
Center top to bottom, or 2 to 3 inches below the top edge.
Shaker fronts: on the top rail
Center the pull on the flat top rail of the frame, or in the center panel.
Drawer stacks: top drawer centered
Center the small top drawer and put the lower pulls near the top edge, where deep drawers are easiest to open.
Size by the rule of thirds
A pull about a third of the drawer width looks balanced, such as a 4-inch pull on a 12-inch drawer.
Wide drawers: two pulls
On 30 to 36 inch drawers, center one pull in each half, or use one long pull.
For pull lengths by drawer width, see what size bar pulls to buy.
Knobs, Pulls or Both?
Knobs on doors, pulls on drawers
A popular mix: drawers are heavier, so a pull gives a better grip.
Knobs on uppers, pulls on base cabinets
Lower cabinets get hardware that is easy to grab.
Pulls everywhere
A clean, modern look, especially on flat slab doors.
One finish for the room
Keep the same finish when mixing knobs and pulls.
Same spacing up and down
Use the same edge distance on wall and base cabinets.
Mind the frame width
On shaker doors, choose a knob no wider than the stile.
Replacing old hardware? See how to upgrade kitchen cabinets with new hardware.
How to Install Cabinet Knobs and Pulls
Five steps for straight, matching hardware.
Pick one spacing
Decide the edge distance and use it everywhere.
Mark on painter’s tape
Tape takes pencil marks and protects the finish.
Set the jig
Hold it tight to the corner and drill straight through.
Back the hole
A scrap block behind the door stops splintering.
Fit one first
Install one door and one drawer, step back, then do the rest.
More cabinet guides: corner kitchen cabinet dimensions, standard base cabinet dimensions, standard upper cabinet dimensions and peel-and-stick cabinet hardware.
Cabinet Knob and Pull Placement FAQs
Where do you put knobs on kitchen cabinets?▼
On the corner opposite the hinges, about 2 to 3 inches from both edges: the bottom corner of upper doors and the top corner of base doors.
Should cabinet knobs go on the top or bottom?▼
Bottom on upper cabinets and top on base cabinets, so they are easy to reach.
Where do you put pulls on kitchen drawers?▼
Centered side to side, in the middle of the front or 2 to 3 inches below the top edge. On shaker drawers, center the pull on the top rail.
How far from the edge should cabinet knobs be?▼
About 2 to 3 inches from the side and from the top or bottom edge. Keep the same spacing on every door.
Do you center pulls on drawers?▼
Yes, side to side. Top to bottom, center them or set them 2 to 3 inches below the top edge.
How many pulls on a 36 inch drawer?▼
Two. Center one in each half, 9 inches from each edge, or set them on the one-third lines. One long pull also works.
Should I use knobs or pulls on kitchen cabinets?▼
Either works. A popular mix is knobs on doors and pulls on drawers.
What size pulls for kitchen drawers?▼
About one third of the drawer width, such as a 4-inch pull on a 12-inch drawer.
The Bottom Line
- Doors: knobs opposite the hinges, 2 to 3 inches from the edges, at the bottom of upper doors and the top of base doors.
- Drawers: pulls centered, with two pulls or one long pull on 30 to 36 inch drawers.
- Tools: a Cabinet Hardware Jig, a Combination Square and a Brad Point Drill Bit.
Pick one spacing, mark it with a jig and repeat it on every door and drawer.
