★ Black Friday · Fri Nov 27★ Cyber Monday · Mon Nov 30★ Shop the deals →★ Gift guides for every cook★ See the gift guides →★ Black Friday · Fri Nov 27★ Cyber Monday · Mon Nov 30★ Shop the deals →★ Gift guides for every cook★ See the gift guides →

Where to Put Knobs and Pulls on Kitchen Cabinets (With Diagrams)

Where to Put Knobs and Pulls on Kitchen Cabinets (With Diagrams)

Knobs go on the corner opposite the hinges, 2 to 3 inches in from each edge: the bottom corner of upper doors and the top corner of base doors. Center pulls on drawers.

Door and drawer diagramsExact spacingInstall tools

Put knobs on the corner opposite the hinges: the bottom corner of upper cabinet doors and the top corner of base cabinet doors, about 2 to 3 inches in from both edges. Center pulls on drawers.

The goal is hardware you reach without stretching or bending: low on wall cabinets and high on base cabinets.

Quick answer

Knobs: opposite the hinge, 2 to 3 inches from the side and from the bottom (upper doors) or top (base doors). Drawer pulls: centered side to side, in the middle of the front or 2 to 3 inches below the top edge. On drawers 30 to 36 inches wide, use two pulls or one long pull.

The placement chart, diagrams and six install tools are below.

Product links go to Amazon. As an Amazon Associate, Kitchen Guide 101 earns from qualifying purchases.

Cabinet Hardware Tools Compared

All 6 side by side. Tap any name to see it on Amazon.

ToolTypeUse onWhenBest forPrice
Cabinet Hardware Jig for Knobs and PullsDrill guideDoors and drawersBefore drillingA full kitchen$$
12-Inch Combination SquareMeasuring toolEdges and centersMarkingChecking spacing$
3/16-Inch Brad Point Drill BitDrill bitWood doors and drawersDrillingStandard 8-32 screws$
Breakaway Cabinet Hardware Screws, 8-32ScrewsDoors and drawersInstallingOdd door thicknesses$
Stainless Steel Bar Pulls, 25 PackHardwareDrawers and doorsFinishingModern kitchens$$
Round Cabinet Knobs, 25 PackHardwareDoorsFinishingShaker doors$$

Details are as stated on each Amazon listing at time of writing and can change. Price tiers: $ under $20 · $$ $20–50.

6 Tools for Installing Knobs and Pulls

A jig, a square and the right drill bit make placement exact. Hardware packs come last.

Best for exact placement

Cabinet Hardware Jig for Knobs and Pulls

Adjustable stopsDrill guide holesWorks on doors and drawersRepeats the same spot$$

A jig sets the spacing once and repeats it on every door. The guide holes keep the drill bit straight, so knobs and pulls line up across the kitchen.

Check the hole spacing range on the listing against the pulls you plan to buy.

Why it made the list

  • Same spot on every door
  • Straight holes
  • Less measuring
Keep in mind

  • Takes a few minutes to set up
  • Check the hole spacing range
Best for: New hardware on a whole kitchen.

Check Cabinet Hardware Jig Price on Amazon →

Best for marking

12-Inch Combination Square

Sliding head locks in place12-inch steel ruleMarks square linesFinds centers quickly$

The tool for measuring in from an edge. Lock the head at your chosen distance and every mark lands the same way on every door.

It also checks that a pull sits square to the drawer edge.

Why it made the list

  • Repeatable marks
  • Squares lines to the edge
  • Useful for other projects
Keep in mind

  • Not a drill guide
  • Measure twice on framed doors
Best for: Marking before drilling.

Check Combination Square Price on Amazon →

Best drill bit

3/16-Inch Brad Point Drill Bit

Sharp center spurClean entry holeClears 8-32 hardware screwsFits any drill$

Most knob and pull screws in the United States are 8-32 machine screws, which pass through a 3/16-inch hole. A brad point starts exactly on the mark and cuts a clean hole.

Clamp a scrap block behind the door so the back face does not splinter.

Why it made the list

  • Starts on the mark
  • Clean holes
  • Low price tier
Keep in mind

  • Check your screw size first
  • Metric hardware can differ
Best for: Drilling new hardware holes.

Check Brad Point Drill Bit Price on Amazon →

Best spare screws

Breakaway Cabinet Hardware Screws, 8-32

Snap to lengthStandard 8-32 threadFits most knobs and pullsBulk packs$

Doors and drawer fronts vary in thickness. Breakaway screws snap off at the length you need, so a screw is never too short or poking through.

They help most on drawers with a separate decorative front.

Why it made the list

  • One pack fits many depths
  • Low price tier
  • Handy for doubled fronts
Keep in mind

  • Check the thread size
  • Snap with pliers
Best for: Thick or doubled drawer fronts.

Check Breakaway Screws Price on Amazon →

Best pulls

Stainless Steel Bar Pulls, 25 Pack

Bulk packSold by hole spacingScrews usually includedSeveral finishes$$

Bar pulls suit modern and transitional kitchens. One bulk pack in a single finish keeps every drawer and door matched.

Check the hole spacing, called center-to-center, before you buy.

Why it made the list

  • Matched finish
  • Easy to grip
  • Enough for most kitchens
Keep in mind

  • Hole spacing must match
  • Two holes per pull
Best for: Drawers and tall doors.

Check Bar Pulls, 25 Pack Price on Amazon →

Best knobs

Round Cabinet Knobs, 25 Pack

Bulk packOne screw eachEasy to installSeveral finishes$$

Knobs need only one hole, so they are the simplest hardware to fit. They suit shaker doors and small drawers.

On a shaker door, pick a knob no wider than the door frame it sits on.

Why it made the list

  • One hole each
  • Quick to fit
  • Classic look
Keep in mind

  • Can spin if not tightened
  • Smaller grip than a pull
Best for: Doors and small drawers.

Check Cabinet Knobs, 25 Pack Price on Amazon →

Where to Put Cabinet Knobs and Pulls: Placement Chart

HardwareWhere it goesSpacing
Knob on an upper doorBottom corner, opposite the hinge2 to 3 in from the side and bottom edges
Knob on a base doorTop corner, opposite the hinge2 to 3 in from the side and top edges
Pull on an upper doorVertical, on the side opposite the hingeBottom end 2 to 3 in above the bottom edge
Pull on a base doorVertical, on the side opposite the hingeTop end 2 to 3 in below the top edge
Knob on a shaker doorCentered on the frame (the stile)Where the stile meets the bottom rail on uppers, the top rail on base doors
Pull on a drawerCentered side to sideMiddle of the front, or 2 to 3 in below the top
Pull on a shaker drawerCentered on the top railMiddle of the rail, or the middle of the center panel
Wide drawer, 30 to 36 inTwo pulls, or one long pullEach pull centered in its half (9 in from each edge on 36 in) or on the one-third lines

Whatever spacing you choose, use it on every door and drawer, on wall and base cabinets alike.

Knob and Pull Placement Diagrams

Gold lines show the measurement from each edge.

2 to 3 inhinge side
Upper door: bottom corner, opposite the hinges
2 to 3 inhinge side
Base door: top corner, opposite the hinges
Drawer: pull centered side to side
Wide drawer: one pull centered in each half

Where to Put Pulls on Drawers

Center side to side

Measure the drawer front and mark the middle.

Slab fronts: middle or high

Center top to bottom, or 2 to 3 inches below the top edge.

Shaker fronts: on the top rail

Center the pull on the flat top rail of the frame, or in the center panel.

Drawer stacks: top drawer centered

Center the small top drawer and put the lower pulls near the top edge, where deep drawers are easiest to open.

Size by the rule of thirds

A pull about a third of the drawer width looks balanced, such as a 4-inch pull on a 12-inch drawer.

Wide drawers: two pulls

On 30 to 36 inch drawers, center one pull in each half, or use one long pull.

For pull lengths by drawer width, see what size bar pulls to buy.

Knobs, Pulls or Both?

Knobs on doors, pulls on drawers

A popular mix: drawers are heavier, so a pull gives a better grip.

Knobs on uppers, pulls on base cabinets

Lower cabinets get hardware that is easy to grab.

Pulls everywhere

A clean, modern look, especially on flat slab doors.

One finish for the room

Keep the same finish when mixing knobs and pulls.

Same spacing up and down

Use the same edge distance on wall and base cabinets.

Mind the frame width

On shaker doors, choose a knob no wider than the stile.

Replacing old hardware? See how to upgrade kitchen cabinets with new hardware.

How to Install Cabinet Knobs and Pulls

Five steps for straight, matching hardware.

Step 1

Pick one spacing

Decide the edge distance and use it everywhere.

Step 2

Mark on painter’s tape

Tape takes pencil marks and protects the finish.

Step 3

Set the jig

Hold it tight to the corner and drill straight through.

Step 4

Back the hole

A scrap block behind the door stops splintering.

Step 5

Fit one first

Install one door and one drawer, step back, then do the rest.

More cabinet guides: corner kitchen cabinet dimensions, standard base cabinet dimensions, standard upper cabinet dimensions and peel-and-stick cabinet hardware.

Cabinet Knob and Pull Placement FAQs

Where do you put knobs on kitchen cabinets?▼

On the corner opposite the hinges, about 2 to 3 inches from both edges: the bottom corner of upper doors and the top corner of base doors.

Should cabinet knobs go on the top or bottom?▼

Bottom on upper cabinets and top on base cabinets, so they are easy to reach.

Where do you put pulls on kitchen drawers?▼

Centered side to side, in the middle of the front or 2 to 3 inches below the top edge. On shaker drawers, center the pull on the top rail.

How far from the edge should cabinet knobs be?▼

About 2 to 3 inches from the side and from the top or bottom edge. Keep the same spacing on every door.

Do you center pulls on drawers?▼

Yes, side to side. Top to bottom, center them or set them 2 to 3 inches below the top edge.

How many pulls on a 36 inch drawer?▼

Two. Center one in each half, 9 inches from each edge, or set them on the one-third lines. One long pull also works.

Should I use knobs or pulls on kitchen cabinets?▼

Either works. A popular mix is knobs on doors and pulls on drawers.

What size pulls for kitchen drawers?▼

About one third of the drawer width, such as a 4-inch pull on a 12-inch drawer.

The Bottom Line

Pick one spacing, mark it with a jig and repeat it on every door and drawer.


© 2026 Kitchen Guide 101 · All rights reserved · Some links are affiliate links

Scroll to Top